SUBSTRATE: SBR/NBR rubber pipes are lined with Hexagonal Ceramic Mosaic. The use of rubber enables the pipes to be highly flexible and since it is lighter than steel can be installed into difficult to reach areas much easier than it is to install the steel equivalent. Good resistance to some chemicals (please contact our technical support before specific applications). Ceramics segments are composed of aluminia and oxide are produced with the most advanced technology, sintering spray-dried powders. The special manifacturing process allows to obtain a very compact structure (porosity 0) and extreme hardness (Mohs scale 9). The special surface guarantees a perfect flow of the material, avoiding any problem related to packing and oxidation
REINFORCEMENT: Reinforced with a continuos steel spiral to ensure that the diameter of the pipe is maintened no matter how it’s bent. Strips of copper also run downthe length of the rubber pipes to prevent a build up of electrostatic.
COVERING: Black, antistatic (R=2.0 M/m), based blend of SBR/NBR, resistant to abrasion and atmospheric agents.
USES: Suitable for pneumatic conveyng (suction and discharge) in industrial applications of dry cement, coal, and RDF (refuse derived fuel from the recovery, synergistic to coal dust), minerals, ceramic powder, glass fiber, and the load of tanks, and storage ware houses and silos.
APPLICATIONS: in the steel mills industries, coking plants, power plants and factories of ceramic, glass, insulation materials an cement etc...
WORKING TEMPERATURE: -30°C (-22°F) TO +70°C (+158°F)
STANDARD LENGHT: Up to a maximum of 15/20 mt
PACKAGING: Wrapped in polyethylene film
TOLLERANCE: RMA steel mandrel
On internal diameter : < = d.i. 38 mm : +/- 0,79 mm
> = d.i. 38 mm : +/- 1,59 mm
On lenght : +/- 1%
N.B. Available on request CERAB
PHYSICAL AND CHEMICAL CHARACTERISTICS OF CERBEST
INNER TUBE: White, smooth, EPDM rubber. The inner tube compound has a linear electric resistance value higher than 1 x 109, according to ISO 8031 Norm.
REINFORCEMENT: High strength synthetic cord.
COVER: Covered with fibre glass, vulcanized, heat resistant.
TEMPERATURE RANGE: -40° +120° The fibre glass cover resists radiant heat up to +530°C.
APPLICATION: Softwall hose for discharge of cooling water in steel mills, foundries, glassworks, and in all cases where a rubber hose is working close to sources of heat. Resistant against splashes of white hot metal.
INNER TUBE: Black, smooth, synthetic rubber.
REINFORCEMENT: High strength synthetic cord and steel helix wire.
COVER: Covered with fi bre glass, vulcanized, heat resistant.
TEMPERATURE RANGE: 40° +90° The fi bre glass cover resists radiant heat up to +530°C.
APPLICATION: Hardwall hose for suction and discharge of cooling water in steel mills, foundries, glassworks, and in all cases where a rubber hose is working close to sources of heat. Resistant against splashes of white hot metal.
INNER TUBE: Black, smooth, synthetic rubber.
REINFORCEMENT: High strength synthetic cord and steel helix wire.
COVER: Covered with fibre glass, vulcanized, and silicon heat resistant.
TEMPERATURE RANGE: -40° +90° The fibre glass and silicon cover resists radiant heat up to +530°C and against splashed of white hot metal.
APPLICATION: Hardwall hose for suction and discharge of cooling water in steel mills, foundries, glassworks, and in all cases where a rubber hose is working close to sources of heat. Resistant against splashes of white hot metal.
INNER TUBE: Black, smooth, synthetic rubber.
REINFORCEMENT: High strength synthetic cord andhelix wire.
COVER: Covered with fibre glass, vulcanized, heat resistant.
TEMPERATURE RANGE: -40° +90° The fi bre glass cover resists radiant heat up to +530°C.
APPLICATION: Hardwall hose for suction and discharge of cooling water in steel mills, foundries, glassworks, and in all cases where a rubber hose is working close to sources of heat. Resistant against splashes of white hot metal. EXTRA FLEXIBLE VERSION.
INNER TUBE: EPDM white smooth, dielectric synthetic rubber.
REINFORCEMENT: High strength synthetic textiles and 2 steel helix wires for more flexibility.
COVER: Covered with fibre glass, vulcanized, heat resistant.
TEMPERATURE RANGE: -40° +120° The fibre glass cover resists radiant heat up to +530°C.
APPLICATION: Hardwall hose for suction and discharge of cooling water in steel mills, foundries, glassworks, and in all cases where a rubber hose is working close to sources of heat. Resistant against splashes of white hot metal.
INNER TUBE: EPDM white, smooth, synthetic rubber.
REINFORCEMENT: High strength synthetic cord and 2 steel helix wires for more flexibility.
COVER: Covered with fibre glass, vulcanized, heat resistant.
TEMPERATURE RANGE: -40° +120° The fibre glass cover resists radiant heat up to +530°C.
BUILT-IN FITTING:
Hose is built around nipple; after being vulcanized, hose and nipple are an integral unit that will not leak or blow out.
APPLICATION: Hardwall hose for suction and discharge of cooling water in steel mills, foundries, glassworks, and in all cases where a rubber hose is working close to sources of heat. Resistant against splashes of white hot metal.
NOTE: HOSE FOR HEAVY APPLICATION
INNER TUBEO: Black, smooth, synthetic rubber.
REINFORCEMENT: High strength synthetic cord. (steel helix wire on request).
COVER: Covered with fibre glass, vulcanized, heat resistant.
TEMPERATURE RANGE: -40° +90° The fibre glass cover resists radiant heat up to +530°C.
APPLICATION: Hardwall hose for suction and discharge of cooling water in steel mills, foundries, in all cases where a rubber hose is working close to sources of heat. Particularly resistant in heavy applications and microswings cycles. Resistant against splashes of white hot metal.
VERSION WITH BEADED ENDS FITTINGS.
INNER TUBE: White smooth EPDM rubber, electrically isolated, suitable for high temperature.
REINFORCEMENT: Synthetic high strength cord.
COVER: Blue EPDM rubber, electrically isolated, abrasion resistance, suitable for high temperature and ozone resistance.
TEMPERATURE RANGE: -40° +120°.
APPLICATION: For delivery of cooling water in the induction furnace used in steel mills.
INNER TUBE: Black, smooth, CR rubber.
REINFORCEMENT: High, strength synthetic cord.
COVER: Black, wrapped fi nish CR rubber.
TEMPERATURE RANGE: -30° +70°.
NOTE: Tube and cover in self-extinguishing rubber in according to the Norm ASTM C-542.
INNER TUBE: Black, smooth, CR rubber.
REINFORCEMENT: High, strength synthetic cord.
COVER: Black, wrapped fi nish CR rubber. Covered with fi bre glass vulcanized.
TEMPERATURAE RANGE: -30° +70° The fi bre glass cover resists radiant heat up to +530°C
NOTE: Tube and cover in self-extinguishing rubber in according to the norm ASTM C-542
APPLICATION: Softwall hose for deliver oxygen in the siderurgical industries, usefull in all cases where a rubber hose is working close to sources of heat.
INNER TUBE: Black, smooth, antistatic NR/SBR rubber which withstands the pas- sage of abrasive materials.
RINFORZO: High strenght synthetic cord, steel helix wire, and antistatic copper wire.
COVER: Black, corrugated (wrapped fin- ish), EPDM rubber, weathering and ozone resistant.
TEMPERATURE RANGE: -40° +70°C.
APPLICATION: Hose for crossing of high abrasive products. Note: Semi-fitting external shell
INNER TUBE: Smooth in thermoplastic polyurethane (TPU) 70 ShA with abrasion loss of 30 mm3.
REINFORCEMENT: High toughness textile inserts, metallic helix wire and copper cable.
COVER: Corrugated (wrapped finish), in black rubber, flame, abrasion, ozone and weathering resistant.
TEMPERATURE RANGE: -30° +80°C.
APPLICATION: Hose for crossing of high abrasive products. Note: available in smooth or corrugated.
NOTE: Available in smooth and corrugated version.
INNER TUBE: Gray, smooth, EPDM rubber.
REINFORCEMENT: High, strength synthetic cord.
COVER: Black, wrapped finish CR rubber.
TEMPERATURE RANGE: +80° +120°.
APPLICATION: Hose specifically designed developed as a protective sheath, water cooling for the feeding cables in the EAF.
NOTE: Tube and cover in self-extinguishing rubber in according to the Norm ASTM C-542.
